MIL-DTL-83495C (USAF)
the last text page supported. Use of foldouts to support a single page task shall be approved by the
acquiring activity (see 6.2).
3.4.2.8 Cross reference. Electronic media requirements: Cross references shall be made by electronic links.
Print media requirements: The JG manual(s) shall contain a minimum of cross references to other than
those procedures or tasks within the same section or subsystem. Cross referencing within the section or
subsystem may be made when the reference applies to a complete task.
3.4.3 Arrangement. The basic contents of the JG manual and its arrangement shall be as follows:
Front Matter
Chapter 1 General Instructions (system peculiar).
Chapter 2 and subsequent Chapters (system maintenance instructions).
3.4.3.1 Front matter. JG manuals front matter shall be prepared in accordance with MIL-STD 38784,
and applicable requirements speciied herein (see 3.1), except no List of Illustrations or List of Tables is
required. Front matter shall consist of the following:
3.4.3.1.1 Table of contents. Table of contents shall list each Line Replaceable Unit (LRU) or item
covered, each function and task for the listed LRU or item, and shall cross-reference the applicable SSSN (if
a function consists of only one task, only the function shall be listed). Each manual of a multi-manual set
shall contain a cross-reference listing of the functions in all other manuals in that series. Tasks shall be
listed only in the JG manual in which they exist (see igure 1).
Electronic media requirements: Table of contents shall be linked to the text to which they apply.
3.4.3.1.2 Foreword. The foreword shall be prepared in accordance with MIL-STD-38784. In multimanual
JGs, only the irst manual shall contain the foreword. Notes explaining the applicability of a system shall be
used, e.g., "This is applicable to F-16C aircraft." When required, the following note pertaining to CPIN
shall be added to the foreword of the JG manual: "NOTE: Refer to the applicable CPIN compendium to
verify the latest version/revision of any computer program coniguration item (CPCI) required to perform
operational checkouts, automatic testing features, etc."
3.4.3.1.3 Safety summary. The safety summary shall be prepared in accordance with MIL-STD-38784.
In multi-manual JGs, only the irst manual shall contain the safety summary. In 5 by 8 inch JGs, the
safety summary shall be the last primary paragraph in the foreword.
3.4.3.2 Chapters. Chapter one shall provide system peculiar information, e.g., speciic torque wrench usage,
lockwire procedures, "O" ring seal installation, and leakage rates. Subsequent chapters shall contain
information applicable to speciic subsystems or parts of the system. Chapter numbering shall continue
through the entire system JG, e.g., XXJG-00-1 has chapter 1, XXJG-10-1 has chapter 2, etc.
3.4.3.2.1 Functions. A maintenance function consists of an input conditions page, a task or series of
tasks, and supporting illustrations (see 6.2p.). Tasks shall be related in nature to the function, e.g., all
tasks supporting the installation of an engine shall relate to and support the installation process and use
the same input condition page. Functions shall not be combined unless supported by the same input
conditions page. An example of a combined function might be "remove and install ampliier". Combined
functions shall not include any subtasks. When typical maintenance functions are used, the task function
within shall be arranged in the following sequence.
a. Operational checkout. Location data for all end-items affected by the check and the primary
equipment required for complete testing of the system shall be included. Normal indications
·
(shown as "dot" results) shall be provided as well as appropriate fault codes, when applicable,
e.g., " MASTER CAUTION light goes out. (33-10-XJ)"
b. Access. All operations necessary to gain access to an item or to remove equipment blocking
accessibility to that item shall be provided. Access panels, screws, and fasteners of different sizes
within the same panel shall be identiied.
c. Remove. All hardware items to be removed shall be speciied by name. Instructions shall be
included for matching, marking, or labeling for reinstallation of any part which could be installed
13
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business