fire munitions and weapons that are approved for loading on an aircraft. This specification provides for electronic delivery of data through the use of the Document Type Definitions \(DTD\) contained in Appendixes A through K \(see 6.2\).

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18

MIL-DTL-9977L(USAF)

3.6.3.2 General. Under this primary paragraph, the following irst subordinate paragraphs shall be covered.

3.6.3.2.1 Scope. The scope shall be in accordance with 3.3.3.2.1.

3.6.3.2.2 SE. SE shall be in accordance with 3.3.3.2.2.

3.6.3.2.3 Speciic safety requirements. Speciic safety requirements shall be in accordance with 3.3.3.2.3.

3.6.3.3 Loading procedures. Under this primary paragraph, the following irst subordinate paragraphs

shall be covered.

3.6.3.3.1 Aircraft preparation. Aircraft preparation shall be in accordance with 3.3.3.3.1.

3.6.3.3.2 Munitions preparation. Munitions preparation shall be in accordance with 3.3.3.3.2. In addition,

this procedure shall include steps required to assemble and install authorized fuzes, prior to munitions

loading. Procedures shall be included to verify the safety of each fuzed munition.

3.6.3.3.3 Cartridge installation. Cartridge installation shall be in accordance with 3.3.3.3.3.

3.6.3.3.4 Loading. This paragraph shall include steps required to load the munition. All steps shall be

singular. Unless otherwise speciied by the acquiring activity, this procedure shall include steps to remove

fuze safety device(s) after munitions are loaded (see 6.2). These procedures shall also include steps to install

fuzes which are not authorized for preloading installation.

3.6.3.3.5 Cartridge installation. Cartridge installation shall be in accordance with 3.3.3.3.5.

3.6.3.3.6 Postloading inspection. This paragraph shall include steps required to ensure that required safety

devices are installed, bombs and fuzes are installed properly, and fuze safety devices have been removed or

installed as required. All steps shall be plural.

3.6.3.3.7 Delayed light or alert. Delayed light or alert procedures shall be in accordance with 3.3.3.3.7.

3.6.3.3.8 Immediately prior to launch. Immediately prior to launch shall be in accordance with 3.3.3.3.8.

3.6.3.4 Unloading procedures. Under this primary paragraph, the following irst subordinate paragraphs

shall be covered.

3.6.3.4.1 Saing. Saing shall be in accordance with 3.3.3.4.1.

3.6.3.4.2 Preunloading. Preunloading shall be in accordance with 3.3.3.4.2.

3.6.3.4.3 Unloading. Unloading procedures shall be in accordance with 3.3.3.4.3.

3.6.3.4.4 Fuze and sensor removal. This paragraph shall include steps required to safe and remove the

fuze or sensor from the nonnuclear munition. All steps shall be singular. The following "NOTE" shall

be placed immediately after the paragraph and preceding the steps:

NOTE

With local commander approval, the following fuzes may remain installed.

3.7 Integrated combat turnaround procedures manual. The contractor shall use the DTD in Appendix E, if

electronic delivery of this manual is required (see 6.2). In addition, for electronic presentation, scrollable

views shall be divided into sections. Capitalization and underscoring of chapter, section, and paragraph titles

shall be in accordance with the requirements of MIL-STD-38784 (This manual shall be arranged as follows:

a. Front matter.

b. Chapter 1 - Prepositioning and munition(s) preparation.

1. Scope.

2. General safety requirements.

3. Emergency procedures.

4. SE

5. Prepositioning/inspection.

6. Munition preparation.